1 ftr-k1 series ?? features ? ? small 40a relay ? ? high temperature grade (-40 ? c to 125 ? c) ? ? contact arrangement form u (form a) ? ? surface mount compatible (re ow capability) ? ? inrush current 80a ? ? coil wire temperature class: h actual marking does not carry the type name: "fbr" e.g.: ordering code: fbr53nd12-y -hw actual marking: 53nd12-y-hw fbr53-hw series compact high power relay 1 pole - 40a (for automotive applications) ?? partnumber information fbr53 n d12 - y - hw [example] (a) (b) (c) (d) (e) (a) relay type fbr53 : fbr53 series (b) enclosure n : plastic sealed (c) coil rated voltage d12 : 9....12vdc coil rating table at page 3 (d) contact material y : silver-tin oxide (e) contact rating hw : 40a
2 ftr-k1 series * minimum switching loads mentioned above are reference values. please perform the con rmation test with actual load before production since reference values may vary according to switching frequencies, environmental contions and expected reliability levels. fbr53-hw series ?? specification item fbr53-hw contact data con guration form u material silver-tin oxide (agsno 2 ) voltage drop max. 100 mv at 1a, at 12v open contact voltage average 1.2m at 7a, 12vdc contact rating 40a , 14vdc (resistive load) max. carrying current 40a max. inrush current 80a inrush min. switching load * 6 vdc, 1a life mechanical min. 10 x 10 6 operations (without contact load) electrical min. 100 x 10 3 operations (14vdc, 20a resistive load) coil data rated power 860 mw operate power 310 mw operating temperature range -40 c to +125 c (no frost) coil wire temperature class h timing data operate (at nominal voltage) max. 10 ms release (at nominal voltage) max. 10 ms (no diode) insulation resistance (initial) min. 100 m dielectric strength open contacts 500 vac (50/60 hz) 1min. contacts to coil 500 vac (50/60 hz) 1min. other vibration resistance misoperation 10 to 55hz double amplitude 1.5mm, direction x, y, z endurance 10 to 100hz double amplitude 1.5mm, direction x, y, z no damage (mechanical and electrical) after test. coil energizing: 1 hr each direction, coil not energized: 1 hr each direction shock misoperation 100m/s2 (11ms), direction x, y, z endurance 1,000m/s2 (11ms), direction x, y, z, each 6 shocks no damage (mechanical and electrical) after test. coil energizing: 3 shocks coil not energized: 3 shocks, total 36 shocks terminal solderability at 270 10c for 3 0.5sec. strength 9.8n (1 kgf) pull force, longitudinal during 10 sec. weight approximately 6 g sealing plastic sealed cat iii
3 ftr-k1 series ?? coil rating fbr53-hw series coil code rated coil voltage (vdc) coil resistance +/- 10% (ohm) must operate voltage (vdc) * must release voltage (vdc) * d09 9 94 5.4 0.7 7.7 (at 125 c) 1.0 (at 125 c) d10 10 177 6.3 0.8 9 (at 125 c) 1.2 (at 125 c) d12 12 167 7.3 1.0 10.4 (at 125 c) 1.5 (at 125 c) ?? reference data note: all values in the table are valid for 20c and zero contact current, unless otherwise indicated. * speci ed operate values are valid for pulse wave voltage.
4 ftr-k1 series fbr53-hw series ?? dimensions ?? dimensions ?? schematics (bottom view) ? mounting hole layout (bottom view) unit: mm ? tube dimensions
5 ftr-k1 series fbr53-hw series 1. general information ? all automotive relays produced by fujitsu components are compliant with rohs directive 2002/95ec including amendments. ? cadmium as used in electrical contacts is exempted from the rohs directives on october 21st, 2005. (amendment to directive 2002/95/ec) ? all our automotive relays are lead-free. ? lead free solder plating on relay terminals is sn-3.0ag-0.5cu, unless otherwise speci ed. this material has been veri ed to be compatible with pbsn assembly process. 2. recommended lead free solder pro le ? recommended solder sn-3.0ag-0.5cu. rohs compliance and lead free information 3. moisture sensitivity ? moisture sensitivity level standard is not applicable to through hole mounted electromechanical relays, unless otherwise indicated. 4. tin whiskers ? dipped snagcu solder is known as presenting a low risk to tin whisker development. no considerable length whisker was found by our in house test. we highly recommend that you con rm your actual solder conditions flow solder condition: pre-heating: maximum 120 ? c soldering: dip within 5 sec. at 260 ? c solder bath solder by soldering iron: soldering iron temperature: maximum 360 ? c duration: maximum 3 sec.
6 ftr-k1 series japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@ft.ed.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia paci c fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ fujitsu components international headquarter of ces ?2011 fujitsu components europe b.v. all rights reserved. all trademarks or registered trademarks are the property of their re spective owners. the contents, data and information in this datasheet are provided by fujitsu component ltd. as a service only to its user and o nly for gen- eral information purposes. the use of the contents, data and information provided in this datasheet is at the users? own risk. fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehen- sive, complete and up to date. fujitsu components europe b.v. and af liated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data , and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness t hereof. nor do fujitsu components europe b.v. and af liated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantab ility or tness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, rel iability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. rev. january 11, 2011 fbr53-hw series
|
